field Replaceable units (FRUs) are modular hardware contents that have the right to be serviced there is no disturbing other components in the system. The adhering to topics discuss working v the Turbo iDDR FRUs.

You are watching: What are the frus on a motherboard?

"Top covering removal" "Front bezel removal" "Rotary encoder removal" "Front panel board removal" "Removable media journey removal" "SATA journey removal" "Front connector board removal" "Fan module removal" "Codec board removal" "Power it is provided removal" "Riser plank removal" "IEEE 1394 adapter removal" "RS-422 adapter removal" "XLR plank removal" "CPU motherboard identification" "CPU motherboard identification" "CPU motherboard installation"

The photos in this topics show how to disassemble. Unless otherwise documented, re-assembly is the reverse.

unless otherwise indicated, you require only a Torx tool with T15 magnetic tip to remove and also replace parts in the Turbo iDDR.

girlfriend can also replace the whole Turbo iDDR as a FRU, as defined in "Replacing an iDDR".

NOTE: just Grass Valley contents are supported. Perform not attempt to use contents procured from a various source. NOTE: perform not discard any hardware unless particularly instructed to execute so.

*

WARNING: To avoid serious injury from high currents, ensure the the strength cord is disconnected prior to removing or replacing any parts.

*

CAUTION: This system consists of board-level components that need to be safeguarded from static discharge and also physical shock. Undertake a wrist strap grounded through among the system"s ESD ground jacks when handling system components.

optimal cover removal

To access the interior hardware, first remove the peak cover together follows:

*

CAUTION: come avoid feasible damage come circuit boards and also other sensitive parts, turn off the iDDR and also disconnect AC power before opening the peak cover or removing any type of internal parts.


*

For an introduction orientation of inner FRUs, refer to "FRU locations".

former bezel removal

To eliminate the bezel, an initial remove the peak cover, then proceed as illustrated.


*

NOTE: when installing the bezel, make sure the bottom tabs room engaged and also the button openings are aligned prior to tightening screws.

rotating encoder removal

To eliminate the rotating encoder, an initial remove the optimal cover and also bezel, then continue as illustrated.


*

front panel plank removal

To eliminate the front panel board, first remove the height cover and also the front bezel, then proceed as illustrated. That is not important to remove the rotary encoder.


*

shown with DVD drive gotten rid of for clarity.

Removable media journey removal

To remove the DVD drive or the REV/DVD drive combo, very first remove the optimal cover and also front bezel, then perform the following:

recognize the relations to the DVD drive or the REV/DVD drive combo, then continue as instructed in the adhering to options: If you have actually a Turbo-1 model (with DVD drive only), over there is one ribbon (IDE) cable connecting come the DVD drive. This is the instance if her Turbo system has either the type I motherboard or the form II motherboard. In this procedure when there is a selection of diagrams, follow those that apply to the DVD drive, as the actions are the exact same for both varieties of motherboards. If you have actually a Turbo-R model (with REV/DVD drive combo) and also the cd driver are connected with just one ribbon (IDE) cable, your Turbo system has a type II motherboard. In this procedure when there is a an option of diagrams, follow those that apply to the type II motherboard. If you have a Turbo-R model (with REV/DVD drive combo) and there space two ribbon (IDE) cables (one for each drive), your Turbo system has actually a form I motherboard. In this procedure as soon as there is a choice of diagrams, monitor those that use to the kind I motherboard.

likewise refer to "CPU motherboard identification".

Disconnect cables as in the complying with diagrams:

DVD journey (with either type of motherboard)


*

REV/DVD combo with kind I motherboard


REV/DVD combo with type II motherboard


The REV journey jumper is in the master position for both the type I motherboard principle cabling (two concept cables: one because that REV drive, one for DVD drive) and the form II motherboard concept cabling (one concept cable with center connector come REV drive and end connector to DVD drive).

To install the replacement DVD drive or the REV/DVD journey combo, reverse the actions in this procedure

SATA journey removal

To eliminate SATA 1 first remove the optimal cover. To eliminate SATA 0, additionally remove the DVD drive, then continue as illustrated.

*

prior to installing the replacement SATA journey in the chassis, remove the brackets on the faulty SATA drive and install lock on the instead of SATA drive.

map SATA cables come the motherboard to verify the connection. Refer to "CPU motherboard removal" for the cabling detail.

after replacing one of two people one SATA journey or both SATA drives, you should restore the system. Describe "Restoring the default system".

front connector plank removal

To remove the prior connector board, an initial remove the height cover, the prior bezel, and also the DVD drive, then proceed as illustrated.


If friend disconnect the former interconnect board wiring from the motherboard, describe "CPU motherboard removal" to re-connect the color-coded wires in the correct orientation.

fan module removal

To remove the pan module, first remove the height cover, then continue as follows:

eliminate screws from the fan as illustrated.


Disconnect the fan cable native the motherboard. Describe "CPU motherboard removal" because that the cabling detail.

Codec board removal

To eliminate the codec board, first remove the top cover, then proceed as illustrated.


after ~ the replacement codec plank is installed, use the system installer process as explained in "Restoring the default system" and select device Update/Repair come ensure the codec board and the mechanism software versions space compatible.

strength supply removal

To remove the power supply, an initial remove the height cover and also the codec board, then proceed as illustrated.

Disconnect power cables on motherboard. Describe "CPU motherboard removal" for cabling detail. Disconnect power cables from DVD journey or REV/DVD combo. Refer to "Removable media journey removal" for cabling detail. Disconnect staying cables, remove fasteners, and remove power supply as illustrated:


Riser board removal

To eliminate the riser board, an initial remove the top cover and also the codec board, then continue as illustrated.


IEEE 1394 adapter removal

To remove the IEEE 1394A adapter, very first remove the top cover and the codec board, then continue as illustrated.

RS-422 adapter removal

To remove the RS-422 adapter, very first remove the peak cover and also the codec board, then proceed as illustrated.


XLR plank removal

To eliminate the XLR board, very first remove the optimal cover, the codec board, and the RS-422 adapter, then proceed as illustrated.


CPU motherboard identification

A Turbo system has either a form I (Intel) motherboard or a kind II (Fujitsu-Siemens) motherboard. Use the details in this section to identify the form of motherboard in her Turbo system.

principle connectors

You can identify the motherboard type by the variety of IDE connectors:


The form I motherboard has actually two concept connectors. This method the REV/DVD combo (if present) is associated with two ide cables. The kind II motherboard has one principle connector. This method the REV/DVD combo (if present) is associated with one ide cable.

ram slot color

you can additionally identify the form of motherboard by the color of the slots that hold the Random access Memory (RAM). You could need to usage a flashlight or other light resource to watch the color.


CPU motherboard removal

To remove the motherboard, first remove every boards in the rear of the chassis, recognize the motherboard type, then do the following:

Disconnect cables together in the complying with diagrams.

form I motherboard


kind II motherboard


eliminate screws together highlighted in the adhering to diagrams:

form I motherboard


Disengage connectors from the rear panel together you remove the motherboard.

CPU motherboard installation

replacement motherboards are kind II motherboards. The faulty motherboard that you eliminated was one of two people a form I motherboard or a kind II motherboard. Describe "CPU motherboard identification" to determine your faulty motherboard.

To install the replacement motherboard, reverse the procedures in the ahead procedure "CPU motherboard removal" because that the type II motherboard, following added steps as shown in the adhering to options:

If the faulty motherboard to be a type I motherboard:

refer to "CPU motherboard identification" to check that the faulty motherboard the you removed was a type I motherboard.

Discard the cable previously used to attach the DVD drive or REV/DVD drive combo. affix the DVD drive or REV/DVD journey combo making use of the brand-new cable the is provided with the motherboard replacement kit: do the connection at the motherboard as thorough in the ahead procedure "CPU motherboard removal" for the type II motherboard. do the connection at the DVD drive or REV/DVD journey combo as instructed in "Removable media journey removal" because that the type II motherboard. ~ the motherboard is installed, you must replace the disk photo on the device drive to assistance the form II motherboard. To replace the decaying image, use the system installer procedure as follows: NOTE: The device installer procedure overwrites all documents on the system (C:) drive. accessibility the Turbo iDDR relax Notes and Installation instructions on the Documentation CD that you obtained with the FRU kit. You have to follow the system installer instructions in the release notes. before the very first startup after motherboard replacement, insert the system installer CD in the iDDR DVD drive. You need to use the device installer CD the you obtained with the FRU motherboard replacement kit. This place the compelled disk picture on the device drive to support the form II motherboard. Restart the iDDR. follow the system installer indict in Turbo iDDR release Notes and also Installation Instructions. To conserve your existing media clips and iDDR construction files, in the device installer application, choose the mechanism Update/Repair option.

If the faulty motherboard was a type II motherboard:

refer to "CPU motherboard identification" to check that the faulty motherboard the you gotten rid of was a form II motherboard.

made decision one that the following choices and continue as instructed:

To minimization replacement steps, reuse the old cable that is still connected to the DVD drive or REV/DVD journey combo. It is identical to the new cable offered with the motherboard replacement kit. If desired, you can discard the old cable and also instead usage the brand-new cable. Do the link at the motherboard as detailed in the previous procedure "CPU motherboard removal" for the kind II motherboard. Make the connection at the DVD journey or REV/DVD journey combo together instructed in "Removable media journey removal" because that the kind II motherboard.

See more: How Much Older Is Obi Wan Than Anakin, How Much Older Is Padmé Than Anakin In Star Wars

NOTE: Make sure you attach the principle cable’s finish connector come the DVD drive and the middle connector to the REV drive. Additionally verify the the jumper top top the REV drive is in the grasp position.
*
*
*
*