In this guide, we go end the most common problems that cause Accura inspect engine light and how you can diagnose the Acura examine engine irradiate yourself.

You are watching: Acura mdx check engine light reset


Acura check Engine Light

Common symptoms the Acura owners notification when CEL comes on are:

Engine Missifre,Car ShakesPoor Acceleration,Variable torque Managemen VTM-4 light OnCheck engine irradiate flashing on and also off.Check engine light, and TCS come on.Check engine light blinking.

What go Acura check engine irradiate mean?

Acura inspect engine light (CEL) turns on come let you the the engine control unit (ECU) has detected a problem.

A fault code is save in the Engine regulate Unit (ECU) and can it is in retrieved v an OBD-II scanner, as presented below.

When your Acura check engine light continues to be on, the problem can be miscellaneous as straightforward as a loose gas cap.

It can also indicate a serious engine issue, a problem with the emission system, or in some situations even one indication of a difficulty with the automatic transmission.

What difficulties trigger the check engine irradiate on one Acura? 


While many possible problems will create the Acura check engine light, friend will find some of the most common problems below.

Worn spark plugsDefective Ignition CoilBad massive Air circulation SensorOxygen SensorCatalytic ConverterLoose Gas CapCrankshaft place SensorBad thermostatA defective coolant temperature sensorEVAP issue

Why is Acura inspect Engine irradiate Flashing On and also Off? 

If her Acura inspect engine light is blinking, that usually means there is an engine misfire.

Fuel is no getting burned in the cylinder. In together cases, the engine will likewise shake noticeably.

Do not drive one Acura for an extended time if the check engine light is flashing. Driving through the check engine irradiate blinking rises the threat of causing damages to the engine.

How to Diagnose and Reset Acura inspect Engine Light

To know why the ACURA check engine light is on, you have to read the codes. This is a an easy procedure the you have the right to perform yourself making use of an OBD-II scanner.

What you Need


The following procedure will permit you to read codes and also reset the check engine light on Acura cars.

Locate OBD-II Port under the dashboard top top the driver"s side. This is a 16-pin port. All 1996 and also newer ACURA vehicles have this port under the dashboard.

Your internet browser does not support video tag.Turn an essential to position II. All the dashboard lights will turn on. Do not start the engine. If her ACURA has a Start/Stop button, friend will should press the Start button without pushing the brakes.
Allow the OBD2 scanner to turn on and connect to your ACURA Engine control Unit (ECU). 
Read Codes. Read ACURA examine engine irradiate codes native the Engine manage Unit (ECU) making use of your OBD2 scanner.
Write down the codes and also research the problem before you replace any type of parts. When you fix the difficulties that you found, come earlier to the main menu, and instead of analysis Codes, select Clear Codes and press OK. 

What does it typical when Acura inspect engine irradiate flashes 5 times? 

Acura inspect engine light may flash five times when you revolve the vital to place II yet don"t begin the car.

This happened when the error codes to be cleared with an OBD2 scanner or if the battery was disconnected.

It means that the emission systems space not checked by the ECU self-test, also known as the emissions readiness test.

After a few driving cycles (usually in ~ a week), emission readiness (I/M) is complete, and you have the right to pass the emissions test.

If the Acura irradiate is flashing five times, you won"t happen a state emissions test until the emission readiness test is completed.

See more: Liters Per Hour To Gallons Per Minute To Liters Per Hour To Gallons Per Minute

Drive the vehicle for a few days, and your Acura inspect engine light need to stop blinking once the I/M test is complete.