good afternoonThere room two because that this model. I have attached pictures and also procedures for both.Do you have a password for this repair? RoyThis is the one top top the earlier of the motorREMOVAL PROCEDURE 1. Turn the steering wheel completely to the left. CAUTION: describe Caution in service Precautions. 2. Raise auto on hoist. 3. Disconnect sensor electrical connector. 4. Remove bolt/screw. 5. Eliminate sensor indigenous engine. 6. Check for the following: 6.1. Examine the sensor because that wear, cracks, or leakage. Replace the O-ring if necessary. 6.2. Lubricate the brand-new O-ring through clean engine oil prior to installing.This is the one behind the crankshaft pulley-block in the prior of the motorREMOVAL PROCEDURE CAUTION: refer to Battery Disconnect fist in organization Precautions. 1. Disconnect the an unfavorable battery cable. 2. Eliminate the serpentine drive belt from crankshaft pulley. CAUTION: describe Caution in organization Precautions. 3. Progressive the automobile on hoist. 4. Eliminate the crankshaft harmonic balancer retaining bolt. 5. Remove the crankshaft harmonic balancer. 6. Keep in mind the routing that sensor harness prior to removal. 7. Remove the harness retaining clip with bolt (1). 8. Eliminate the sensor electric connector. 9. Remove the sensor bolts (2).10. Remove the sensor.If you change the one behind the crank pulley, it needs to have a relearn procedure done through a scan tool.The crankshaft position mechanism variation compensating values space stored in the PCM non-volatile memory after a discover procedure has actually been performed. If the actual crankshaft position mechanism variation is not within the crankshaft position mechanism variation compensating values stored in the PCM, DTC P0300 may set. Refer to Diagnostic assist for DTC P0300.The Crankshaft Position system Variation find out Procedure need to be carry out if any of the following problems are true: DTC P1336 is set. The PCM has been replaced. The engine has been replaced. The crankshaft has been replaced. The crankshaft harmonic balancer has been replaced. The crankshaft position sensor has been replaced.IMPORTANT: The scan tool crankshaft position device variation learn duty will it is in inhibited if engine coolant temperature is much less than 70 C (158 F). Permit the engine to warmth to at least 70 C (158 F) before attempting the crankshaft position mechanism variation discover procedure.The scan device crankshaft position device variation learn duty will be inhibited if any type of powertrain DTCs other than DTC P1336 are set before or throughout the crankshaft position system variation learn procedure. Diagnose and repair any type of DTCs if set.The crankshaft position mechanism variation learn role will it is in inhibited if the PCM detects a breakdown involving the camshaft position signal circuit, the 3X reference circuit, or the 24X recommendation circuit. If the scan tool shows a difficulty with the video camer signal, refer to DTC P0341 Camshaft place (CMP) Sensor Performance. If the scan tool shows a difficulty with the 3X crank signal, describe DTC P1374 3X referral Circuit. If the scan tool shows a difficulty with the 24X crank signal, refer to DTC P0336 24X recommendation Signal Circuit. 1. Depress and also hold the service brake pedal. 2. Block the drive wheels. 3. For sure the hood is closed. 4. Begin the engine and allow engine coolant temperature to with at the very least 70 C (158 F). 5. Revolve OFF the ignition switch. 6. Choose the crankshaft position variation learn procedure from the scan tool special functions list. 7. Follow the instructions shown on the scan tool. If the procedure is terminated, describe Important above for instructions. 8. Observe DTC standing for DTC P1336. 9. If the scan tool indicates that DTC P1336 ran and passed, the crankshaft position device variation find out procedure is complete.


You are watching: 2001 pontiac grand am crank sensor location


See more: This Is What Does Monkey Meat Taste Like ? What Does Monkey Meat Taste Like

If the scan tool indicates DTC P1336 fail or not run, inspect for various other DTCs. If no DTCs